Can't record in Acid pro 3.0 using Aardvark Q10 ... Help! -ACID Product Family

Subject:Can't record in Acid pro 3.0 using Aardvark Q10 ... Help! Posted by: straticus Date:1/27/2003 9:09:25 PM Hello people, I just hooked up a new interface, the Aardvark Q10. Other than that everything was existing and was working properly. My old interface was a Seasound Solo ex. I'm running 98se. Problem: When I try to record an analog track the meters in the record dialog box don't show any incoming signal. When I check the recording device drop down menu it shows Microsoft Sound Mapper and also has right and left choices. If I go to options > preferences > audio, it shows Microsoft Sound Mapper or Windows Classic Waves driver in the drop down menu. If I click advanced, all of the Q10's in and outs show up but no matter what I click on, "apply" never becomes active (it remains grayed out) so I can't make any changes stick. I'm not sure if that's where the problem is but that's what I've found so far. BTW, I don't have any problems recording through the Q10 in Samplitude Pro on the same computer. So the Q10 is working correctly. This problem only exists when using Acid. Thank you very much for any help. peace ............... BC :)
Subject:RE: Can't record in Acid pro 3.0 using Aardvark Q10 ... Help! Reply by: RasKeita Date:1/28/2003 11:22:14 AM try selecting the Windows Classic Wave Drivers, then select the the source. When you're in the advanced section you've got to uncheck the interpolate box then recheck it now apply will become available...Level Vibes
Subject:RE: Can't record in Acid pro 3.0 using Aardvark Q10 ... Help! Reply by: straticus Date:1/29/2003 8:51:35 PM Hey RasKeita That did it! Thanks man! I coulda' sworn I tried that before .................. I guess not. Anyway, thanks again! peace ................. BC

Subject:Can't record in Acid pro 3.0 using Aardvark Q10 ... Help!

Posted by: straticus

Date:1/27/2003 9:09:25 PM

Hello people,
I just hooked up a new interface, the Aardvark Q10. Other than that everything was existing and was working properly. My old interface was a Seasound Solo ex. I'm running 98se.

Problem:
When I try to record an analog track the meters in the record dialog box don't show any incoming signal. When I check the recording device drop down menu it shows Microsoft Sound Mapper and also has right and left choices.

If I go to options > preferences > audio, it shows Microsoft Sound Mapper or Windows Classic Waves driver in the drop down menu. If I click advanced, all of the Q10's in and outs show up but no matter what I click on, "apply" never becomes active (it remains grayed out) so I can't make any changes stick. I'm not sure if that's where the problem is but that's what I've found so far.

BTW, I don't have any problems recording through the Q10 in Samplitude Pro on the same computer. So the Q10 is working correctly. This problem only exists when using Acid.
Thank you very much for any help.

peace ............... BC :)

Subject:RE: Can't record in Acid pro 3.0 using Aardvark Q10 ... Help!

Reply by: RasKeita

Date:1/28/2003 11:22:14 AM

try selecting the Windows Classic Wave Drivers, then select the the source. When you're in the advanced section you've got to uncheck the interpolate box then recheck it now apply will become available...Level Vibes

Subject:RE: Can't record in Acid pro 3.0 using Aardvark Q10 ... Help!

Reply by: straticus

Date:1/29/2003 8:51:35 PM

Hey RasKeita
That did it! Thanks man! I coulda' sworn I tried that before .................. I guess not.
Anyway, thanks again!

peace ................. BC