Subject:CD Burning Problem

Posted by: kleb

Date:10/4/2002 6:07:29 PM

I removed Sound Forge Studio. I did a clean install of Sound Forge 6.0. I have Roxio CD Creator 5.1. Now my CD burner does not function properly with either Roxio or Vegas/Forge! Blank CDR media shows up as unrecordable...

Should I re-install Roxio?

Kurt

Subject:RE: CD Burning Problem

Reply by: MJhig

Date:10/4/2002 11:06:27 PM

Roxio has a repair function in add/remove programs, may not help but can't hurt.

MJ

Subject:RE: CD Burning Problem

Reply by: beeper99

Date:10/5/2002 12:06:04 PM

Perhaps you may have already done this..... I would first check to see if my computer recognizes the CD burner. Why not put a disc that already has some information recorded on it in the burner and then go to Windows Explorer to see if the CD Burner drive and the data on the disc can be found there? If the results are positive, you then know the problem resides with the applications rather than the hardware.

Sometimes I have had similar problems and later found out the disc I had put in the burner was defective. Since I use the cheap ones, at times I have had to put in two or three before one worked right.

Reinstalling Roxio is no big deal. It takes only a few minutes. I would do a clean install rather than over the one already on the hard drive.

Subject:RE: CD Burning Problem

Reply by: kleb

Date:10/5/2002 5:51:25 PM

Thanks for the help. After rebooting, Roxio works fine. The problem is in VV3. Here is the error using VV3 to burn a DAO CD. Then, running Roxio & checking disk information, the cd shows up as audio & unrecordable!

The drive has received an illegal command.

'Teac CD-R50S,CD-R55S'-(5)
'aic78u2'-(2)
-'TEAC CD-R55S 1.0R'-(2)
Module cdr50s.cpp Line 1697
An illegal request was received.
The parameter list length is incorrect.

Status: 00020202
Command: c2 00 00 00 00 00 00 00 04 00
Sense: 05 1a 00
Info: 00 00 00 00
Specific: 00 00 00
Extra: 00 00 00 00 00 00 00 00 00 00

Subject:RE: CD Burning Problem

Reply by: Sony_DaveS

Date:10/7/2002 1:48:30 PM

What OS is this?

Subject:RE: CD Burning Problem

Reply by: kleb

Date:10/7/2002 10:14:25 PM

Good question. The error ocurrs with Win2k Pro.

[The rest of the system - Time to updgrade!)
AMD 751 Processor
ASUS K7M Slot A Motherboard, VIA KX133 Chipset
512 MB RAM
Western Digital 15GB (OS/APPS)
IBM SCSI 9GB (recording)
Adaptec Ultra2 SCSI (PCI Interface)
MS Windows 2000 Profesional, SP3 Build 2195(dual boot w/ Win98 SE)
M-Audio DiO 2448
Latest Vegas, Acid, Sound Forge

Subject:RE: CD Burning Problem

Reply by: Sony_DaveS

Date:10/8/2002 11:49:19 AM

Kurt - please check your email. I sent you some info that might fix this burner in our applications.

Thanks.

Subject:RE: CD Burning Problem

Reply by: kleb

Date:10/8/2002 2:09:21 PM

Thanks Dave...

Wow It worked! I am very impressed by the response time. Thank you very much. Vegas now recognizes the CD as recordable in my TEAC drive. The test write completed without errors.

Since I dual boot, I ran the update in both Win2k Pro and Win98 SE. I ran a DAO Test only (did not burn the CD). Interestingly, I had to Prerender to a temporary file in Win2k Pro while I did not have to in Win98 SE.

However, Now Roxio Easy CD Creator is not working in Win2k Pro at all. Disc Information on blank media shows Drive: TEAC CD-R55S, Disc Type: Audio CD "", Writability: Non Recordable.

Since Vegas works now, I'll bring this up with Roxio after trying a reinstall...

Great job!

Kurt

“The difficult you did immediately"